Furnace Repair in Battle Creek

When your furnace in Battle Creek blows cold air, it might be due to something simple or more complex. Start by checking your thermostat to ensure it’s set to heat and not just the 'Fan' setting. If the thermostat isn’t the issue, the problem could be with the flame sensor or ductwork leaks. Our technicians can quickly diagnose and fix the problem for you.

Furnace repair costs in Battle Creek vary widely based on the complexity of the issue. Smaller problems like sensor replacements can cost as little as $100, while major repairs like heat exchanger replacements may cost thousands. Most standard repairs range between $300 and $800. Older systems tend to have more expensive and frequent issues, so regular maintenance is key to minimizing long-term costs.

Before contacting a professional for furnace repair in Battle Creek, checking these items can potentially save you a service call:

• Replace dirty air filters

• Confirm your thermostat is set correctly

• Ensure the pilot light is lit

• Verify the furnace circuit breaker hasn’t tripped

• Open any closed or obstructed air vents

If these basic steps don’t solve the problem, call J and J for professional assistance.

If your furnace in Battle Creek is making unusual noises, it’s a clear sign of a mechanical issue that needs attention. Common causes include:

• Dirty burners causing booming sounds

• Cracked heat exchangers making popping noises

• Faulty blower motors buzzing or grinding

• Loose screws or bolts rattling during operation

• Expanding or contracting ductwork

Ignoring these noises could lead to further damage or system breakdown. Contact (269) 965-1627 to schedule a prompt repair.

Water leaking from a furnace might seem odd, but newer high-efficiency systems often create condensation. If the water is pooling, the issue is likely a clog. Common causes include:

• Clogged condensation drains

• A damaged heat exchanger

• Faulty condensate pumps

• Air conditioner or humidifier issues

Leaking water can cause significant damage to your furnace components and surrounding property, so call (269) 965-1627 to address the problem right away.

Older furnaces in Battle Creek may have a standing pilot light that occasionally goes out. It is possible to relight it safely if you follow the correct procedure:

1. Turn off the gas and wait five minutes.

2. Adjust the gas valve to “Pilot” and press the reset button.

3. Use a long lighter to ignite the flame.

4. Once the light is steady, release the button and turn the valve to “On.”

If it doesn’t stay lit, contact J and J for assistance.

A cracked heat exchanger is a serious safety issue for furnaces in Battle Creek. It can cause incomplete combustion, allowing carbon monoxide—a deadly gas—to leak into your home. Replacing a heat exchanger is costly, so it’s often more economical to replace the entire furnace. Our experts can assess the danger and recommend the best option for your home.

A cheap furnace repair might seem like a good deal, but it often leads to problems like:

• Inferior parts that fail quickly

• Incomplete system inspections

• Unskilled technicians

• Pushy contractors recommending unnecessary replacements

• No warranty on the work

Choose J and J for reliable, high-quality furnace repairs.

At J and J, we repair all major furnace brands in Battle Creek, including Lennox, Carrier, Trane, and Goodman. No matter the make or model, our experienced technicians know how to diagnose and fix any issue your system might have.

Strange smells from your furnace in Battle Creek can be caused by:

• Burning dust during startup

• Mold or mildew in the system

• Electrical burning from a short circuit*

• Rotten egg smells from a gas leak*

• Grime in the heat exchanger

If you smell gas or burning, turn off your furnace and call (269) 965-1627 immediately.

Routine maintenance is key to extending your furnace’s lifespan. Schedule annual tune-ups with J and J, replace filters regularly, and address minor issues like strange noises or thermostat problems before they worsen. Preventative care helps avoid costly repairs.

If your furnace clicks on and off repeatedly (short cycling), it might be time to clean the flame sensor. Here’s how:

• Turn off power and gas to the furnace

• Locate the flame sensor near the burner

• Remove the sensor and clean it with fine-grit sandpaper

• Replace the sensor and restore power

If you’re uncomfortable doing this, call J and J for help.

While minor fixes like changing filters are fine for DIY, most furnace repairs should be left to certified professionals. Furnaces involve electrical, gas, and mechanical components, making them potentially hazardous. For safe and effective repairs, contact J and J.