Turning On the Heat for the First Time This Fall: A Simple Michigan Routine

Every fall there is a night when the house gets cold enough that someone finally walks to the thermostat. Turning on the heat for the first time after a summer off is usually uneventful, but a furnace that sat idle for months in a Southwest Michigan basement deserves a few minutes of attention first.

Before turning on the heat for the first time, replace the filter, clear the registers and returns, test your carbon monoxide alarms and set the humidifier for winter. Switch the thermostat to HEAT, let the furnace run a full cycle, and watch for anything beyond a brief dusty smell.

This is the homeowner routine, not a replacement for a professional tune-up. It does not take long, and it catches the problems that would otherwise show up on the first truly cold night.

1. Replace the Filter Before the First Cycle

Start with the filter before turning on the heat. It did the air conditioner’s work all summer too. If it is gray and packed, it will restrict airflow the moment the blower starts, and restricted airflow is behind a long list of heating problems.

Put in a fresh filter of the right size, with the airflow arrow pointing toward the furnace. If the size is printed on the old filter’s frame, write it down somewhere you will find it. You can order furnace filters online and keep a spare on the shelf for midwinter.

2. Clear the Registers, Returns and Furnace Area

Summer rearranging tends to put a couch over a floor register or a toy bin in front of a return. Before turning on the heat, walk the house and open every supply register. Make sure nothing blocks the return grilles, the larger ones that pull air back to the furnace.

Then look at the furnace itself. Basement storage creeps toward it over the summer. Keep boxes, paint cans, laundry and anything that can burn well away from the furnace and water heater, and leave a clear path so a technician can work on it if needed.

3. Test Your Carbon Monoxide Alarms

Your furnace burns fuel inside the house, so this is the step not to skip before turning on the heat. Press the test button on every CO alarm and replace the batteries in any that use them. Check the date on the back, since alarms have a limited service life and the manufacturer lists when to replace them.

The EPA points to the Consumer Product Safety Commission’s recommendation that every home have CO alarms on each level, outside each sleeping area. If you are short, add them now. Our carbon monoxide and furnace safety guide explains the warning signs and what to do if an alarm sounds.

4. Set the Humidifier for Winter

If a whole-house humidifier is mounted on your ductwork, it probably sat idle all summer. Many bypass humidifiers have a damper on the bypass duct with summer and winter positions. Move it to winter and turn the water supply back on.

Look at the water panel, sometimes called the pad. If it is crusted with white mineral scale, replace it. Then set the humidistat modestly and lower it as outdoor temperatures drop, which keeps condensation off the windows.

5. Switch the Thermostat to HEAT and Start a Cycle

Set the thermostat mode to HEAT and the fan to AUTO, then raise the setpoint a few degrees above room temperature so the furnace gets a clear call. On a smart or programmable thermostat, make sure a summer schedule or cooling hold is not overriding the change.

Within a few minutes you should hear the sequence: the small inducer motor starts, the burners light with a soft whoosh, and after a short delay the main blower comes on and warm air reaches the registers.

If nothing happens at all, work through our guide to a furnace not turning on. If it runs but the air stays cool, see furnace blowing cold air.

6. Expect a Brief Dusty Smell, and Know What Isn’t Normal

Dust settles on the heat exchanger and burners over the summer. When they heat up, that dust burns off, so a faint, dry burning smell for a short time after turning on the heat is normal. Opening a window helps it clear.

Other smells are not part of the routine:

  • Rotten eggs or sulfur: possible gas leak. Leave the house and call your gas utility from outside.
  • Hot plastic or an electrical odor: shut the furnace off at the service switch and call.
  • Burning dust that lingers through several cycles: worth a service call.

Our guide to furnace smells goes through each odor in more detail.

7. Let It Run a Full Cycle and Listen

Stay nearby for the first full cycle after turning on the heat. A healthy furnace lights smoothly, runs until the thermostat is satisfied, shuts the burners off, and lets the blower run a little longer to pull the last heat out of the exchanger.

Watch and listen for:

  • A bang or boom when the burners light.
  • Grinding, squealing or a loud hum from the blower.
  • Burners that light, shut off within seconds and try again.
  • A status light blinking a fault code.
  • Water around the base of a high-efficiency furnace.

A loud bang at ignition means shut it off and call. The other items deserve a service visit soon, before you depend on the furnace every night.

Homeowner adjusting the thermostat before turning on the heat for the season

Check Outside Before Turning On the Heat

Two things outside the house matter when the season changes. If you have a high-efficiency furnace, find the two white PVC pipes where they leave the wall. Clear away leaves, mulch, nests and anything stacked against them. A blocked pipe trips the pressure switch and stops the furnace.

Then look at the outdoor air conditioner. With a gas furnace, it is done for the year, and our guide on how to shut down your AC for winter covers the simple steps. If that outdoor unit is a heat pump, it is now your heat source, so keep it clear of leaves now and snow later.

White farmhouse under fall maples, the time of year for turning on the heat in Michigan

Turning On the Heat Is Step One. A Tune-Up Is Step Two.

The homeowner routine covers the basics. A professional tune-up goes further: cleaning the burners and flame sensor, testing the ignitor, checking gas pressure, measuring temperature rise, inspecting the heat exchanger and venting, and testing the safety controls. Our furnace tune-up checklist lists what that visit should include.

The Comfort Plus Priority Services Membership is free to join and includes a fall furnace tune-up at $79, a reminder postcard, no overtime charges and no diagnostic charge when a repair is performed. It is the simplest way to stay on top of furnace maintenance without tracking dates.

J&J has served homes across Jackson, Charlotte and the surrounding area for over 50 years. If anything about turning on the heat looked, sounded or smelled wrong, call (269) 965-1627 Monday through Friday, 8:00 a.m. to 5:00 p.m.

Turning On the Heat FAQs

Is it normal to smell burning when turning on the heat for the first time?

A faint, dusty burning smell is normal. Dust that settled on the heat exchanger over the summer burns off during the first cycles and should fade quickly. A rotten-egg smell, an electrical odor or smoke is not normal: shut the furnace off and call, or leave the house if you smell gas.

When should I turn on the heat in Michigan?

There is no single date. Most people switch over when nights get cold enough that the house stays uncomfortable into the morning. The better habit is to run a first heating cycle early in the fall, on a mild day, so any problem shows up before you need heat every night.

Should I get a furnace tune-up before turning on the heat?

Ideally, yes. A fall tune-up catches dirty flame sensors, weak ignitors and venting problems before the first cold snap. If the furnace is already running well, schedule the tune-up soon anyway. Comfort Plus members pay $79 for the fall furnace tune-up.

Ready for heating season? Call J&J at (269) 965-1627 or schedule a visit today.